The Orange Peel Surf Wax Mold (My Review)

I was a Kickstarter supporter for The Orange Peel, a new surf wax gadget that just shipped out to most of us last week who bought in to the concept. I felt like doing a review of this product, so here it is. Did I get it for free? Hell nah, brah. These opinions are all Average Surfer Approved, and that’s all that matters, Bro-tein Shake.

The Orange Peel (peelitout.com, $11.99) is a 100% silicone cup that’s meant to fit into your car’s cup holder, and collect the gnar bits of surf wax that end up in your car. Unfortunately, this silicone cup was a little too small and got “lost” in my Surfmobile’s (Yaris) oversized side door cup holders, so it’s going to have to sit in the open middle console instead. Here it is in my grody Surfmobile:

The actual surfy-special feature of this mold cup is a raised strip of silicone along the bottom of the inside. This allows the mold to create the traditional break line for the bar of surf wax after melting it into the mold, creating the distinct halves. A half a bar is enough to wax up a longboard for a sesh, and fits into a pocket easily.

That feature is what makes the mold stand out for me. There are plenty of silicone molds out there for far cheaper in the craft store’s baking section, but as a surfer, I like the simple and practical addition of this line in the mold that creates a truly usable bar of surf wax.

To test this new mold, I used an actual old gnarly ball of surf wax from under the seat of my car, and rolled it around in more sand from the car. Yummy.

Here’s your WARNING WARNING WARNING!

Although the Orange Peel cup itself alone is microwaveable, you SHOULD NOT microwave things with sand all over it. Here in Cocoa Beach, a lot of our sand is dredged from shoals off the Cape, and there can often be trace metals in the dredge material. NOT a good thing to put in the microwave.

For this experiment, I used the little toaster oven we picked up at Goodwill. It stays out in the garage, so I use it for melting small amounts of wax sometimes, but mostly it’s for baking modeling clay (no fumes in the house, bonus).

I heated the clump in the toaster oven at 250 degrees Fahrenheit (recommended by Peel Surf) for 20 minutes. This wax was most likely “Tropical” hardness from throughout this Summer and Fall, so I figured I would need to heat it for a while for it to melt sufficiently. The sand and debris in the wax will tend to fall toward the bottom of the cup. After I removed it from the oven, I made sure to give it a little stir to help things along.

Allow it to set for at least an hour. I left mine to harden overnight.

It came out of its mold with some difficulty because of the thickness of the cup’s walls. It’s a sturdy design, but it also makes it tricky to pop out easily without damaging the edges of the finished wax bar a bit.

Once the bar was out, I just scraped off the sludge that had settled to the bottom, which is now at the top of the bar of wax. I still had quite a bit of clean wax that remained.

Done!

Ok, so here’s my overall impression…..

Pros:

  • Makes a decent sized, good looking bar of wax
  • Molds a deep, easy-to-break line in the center
  • The bright color of The Orange Peel makes it easy to spot in a dark car in the morning

Cons:

  • Expensive- the price point of 12 bucks needs to be reduced to make this product work, or else I’m using my old muffin cups
  • May disappear into the cup holders of many cars with oversized holders

My suggestions:

  • Please get the price down- nice concept, but most surfers will have trouble justifying the expense, even to recycle their wax and Save Da World.
  • Include a simple Recipe Book- a lot more people might buy your product if you include some fun how to’s, similar to a Surf Wax Making Kit.
  • Introduce a “Jumbo” Orange Peel for oversized drink holders, and people who want to make larger bars of wax.
  • Consider a Glow In the Dark version for those Dawn Patrol sessions.
  • Offer unique molds (flower shapes, animals, etc.) with break lines through them. Only the inside of the cup needs to be shaped, the outside of the cup can be smooth, so it can still fit into a drink holder nicely.

I’ll definitely be using this cool little mold often, but I’ll be waiting on buying anymore “Peels” until the price drops a bit. BUT, if there’s a surfer you want to splurge on, this might be a fun gift to give along with some natural beeswax (and show them how to make their own surf wax too!).

5 thoughts on “The Orange Peel Surf Wax Mold (My Review)

    1. Yeah, they envisioned taking the leftover bits and chucking them in this cup. I like the mold idea featuring the break line, but itโ€™s pricey right now for a silicone cup when thereโ€™s a lot of competition out there for a lot cheaper. It just happens to be in the Baking Section…๐Ÿ˜‚๐Ÿฅง๐Ÿฐ๐ŸŽ‚

      Liked by 1 person

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google+ photo

You are commenting using your Google+ account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s