DIY 4Ocean Charm Earrings

Remember that necklace/wrap bracelet I made a couple of posts ago? I saved the little silver charms from the 4Ocean bracelets, and I wanted to use them to make some easy fun earrings with basic stuff from the craft store. Ear hooks, a few glass beads, and a couple of eye pins can make a fancy looking pair of earrings. You’ll also need a pair of small round-nose jewelry making pliers (here’s a link to some I found online).

All of my supplies

Adding a charm to the end of each eye pin

Sliding a silver bead, a glass fish bead, then a silver bead onto each eye pin

Preparing to make a loop at the top of each eye pin

I try to match up the same position when I make the loop on each

Done!

Ear selfie

These are a cute way to promote the 4Ocean cause of removing plastics from the ocean, and creating awareness of plastic pollution.

Honestly, though, for surfing the Cocoa Beach Pier, I need more useful earrings. I searched on Etsy and found my dream pair:

OFF MY WAVE WANKER

DIY Surf Wax Soap

Another blog I enjoy reading is Oh Yes They Did! They are Mother/Daughter bloggers in Canada, but that’s forgivable….they do some really cool crafts anyway.

One craft they did a while back was using soap base from the craft store to make your own custom molded soap.

So, I thought it would be neat-o to use my Orange Peel surf wax mold to make some soap too.

I picked up some opaque white Shea Butter soap base from my local Michael’s- with my coupon, I got 2 pounds for around 6 bucks. Not bad. I picked out some additional oils and scents to add in too.

The Orange Peel mold with the soap ingredients

Since the typical bar of of surf wax is between 80 to 85 grams, I used my fun monkey peeler to shave off enough soap flakes to make almost 85 grams, since the consistency is very similar to cold water wax. I bought 2 pounds, so I can make at least 10 whole bars.

Working hard

Yes, I tared it with the mold…

Adding in a bit of coconut oil- you can also use the microwave to melt the wax in the silicone mold

I added a lot of the Lor-Ann flavor to get the smell

Soap poured into the mold

I took the soap out of the mold a few hours later, but I allowed the soap to cure for a few days on some paper towels.

Done!

This could get fun….

Ok, so yeah, I can see where this would make a wicked practical joke on a fellow surfer….not that I endorse such things.

Please report any successes back here, though.

Hey- that’s not sick and twisted, but THIS is. I mean, who thinks this makes the perfect guest soap for your bathroom? Yes, this is actual decorative soap:

Looks so nice above the toilet

Surfboard Fin System Blues

I’ve never been a huge fan of the current surfboard fin systems available.

Everyone’s got a favorite

To the uninitiated, there are basically two big players in the “fin system” market currently: FCS and Futures. They are the iPhone and Android of the Surfboard Fin World, and have superfans who are just as rabid. Once you pick a fin system to go into your board, you’re stuck with fins made for that system. It’s like only shopping at Google Play for eternity. Great.

 

FCS has upgraded their systems recently to allow you to snap in your fin without needing the tiny screws anymore. Supposedly.

img_1831

img_1821

Lost one of my special FCS II compatible quad fins that way during a surf, so now I’m back to the tiny freakin’ screws set into the old crappy plastic box. And these other quads STILL back out on me, causing the fin to begin to lift out of the box. I discovered this happening again the other day:

watermarked1(2018-06-02-1350)

This keeps on happening

It’s absolutely absurd to pay this much money for screws that back out, systems that don’t latch, plus the cost of lost fins, which get hella pricey. No wonder FCS has a whole page dedicated to replacement FCS fins. Hmmmm….it’s not because yer a gnar shredda, brah.

Once again, I went back to the online hardware store to find some screws- some call them “grub” screws- a bit longer than the others made of quality 316 stainless steel that are MUCH cheaper than what FCS and Futures sells these for in surf shops.

Link to the screws I bought online here– I don’t get anything for this, it’s just info.

watermarked4(2018-06-02-1350)

The ones I ordered are da best since they’re not marked up 1000%

watermarked3(2018-06-02-1350)

Share with ya friends, wanker

These still sit flush when screwed in, and maybe they might have a better chance of staying in. And now when I lose one, it won’t cost a fortune. I have some boards that use Futures Fins, which only require one screw, but it’s the same length as the one I ordered, but I believe these are better quality for approximately 10 cents each. Sooooo much cheaper.

watermarked5(2018-06-02-1350)

Doesn’t stick out

watermarked6(2018-06-02-1350)

I replaced all eight

I really wish these companies would step up their game since they seem to be monopolies in the surfing world, much like Clark Foam was years ago.

The Surf Industry is just like any other industry, though….

img_1832

And people take me to the cleaners daily