Beater Bodyboard Paipo Sock

All week it’s been gnarlicious around here due to some storms out in the Atlantic plus quite a bit of local winds. When the waves begin to get crazy, I’ll bust out my 54″ Twin Fin Beater board, that I can use as a giant bodyboard. Because it’s a soft board, I don’t need my helmet and crayons like I normally would. Bonus.

Nice wax job

Since I wanted to throw it in the car to surf yesterday evening, I wanted to make a sock for it with a quickness. I’ve done this project for my funshape, but this time, the board is small enough to put on my cutting table directly, so I can wing it even faster.

Ugly fabric? Check.

I used some remnant Lycra spandex fabric I got a long time ago that was sitting around. It’s ugly, but Lycra spandex that’s cheap is always useful for something when you’re in the water a lot.

I folded the fabric right sides together, with one side being the fold, so I won’t need to sew/serge this edge.

Putting my board on the fabric for layout

I even used my French curve to trim the nose!

After cutting

I used my rotary cutter to cut this Lycra- much faster. I also used a serger for this project.

Serging the sides

Fit check

Trimming off excess for the casing

I used the extra at the bottom opening, folded it over, and reattached a casing for an old shoelace. Made a perfect closure.

Reinforcing the pull through site

Reattaching the casing to the bag

I used an old shoelace

Cool beans

Done!

It’s great in da surfmobile, and now I can just keep my little 5′ leash on the board without worrying about it dragging everywhere. The sock stretches over the board super easy.

In da car

Pink and paisley

So I got to play around in the gnar for a bit yesterday afternoon, since the surf sock only took an hour. Here’s a pic I took from last night:

Just do it

Once again, my tradition of procrastination lives on….

I would have been too lazy to do this in high school

Big Blue Button Amigurumi

Jellyfish are often misunderstood creatures in Florida, especially since they often hurt surfers with stings that range from annoying to scream worthy.

I’ve had my fill for a lifetime, believe me.

In actuality, many of these “jellyfish” are groups of polyps clinging together, drifting with the ocean’s currents. These type are known as Chondrophores, which include the Man O’ War, a particularly famous critter that gives humans a painful sting. However, there are other types of unique Chondrophores here in Florida that don’t pack quite the wallop.

Blue Button

Blue Buttons are part of this group, and can be found in Florida quite often. They are small (usually only 1-2 inches in diameter), but they are beautiful to look at. So, I decided to make a jumbo, huggable version out of yarn. Just because, of course.

Below I’ve shown a bit of my process in pictures for those into amigurumi:

I used three basic blues with a 3.5 mm hook

Making a circle for one side, starting to change color to make stripe

Using a half- color change technique

Top half done- I made it a bit taller

Bottom half

Two halves complete

Each tentacle is from 5-8 inches

Lots o’ tentacles

Pulling each tentacle into the half

Knotted inside and ends trimmed

Placing eyes

Stuffing and sewing shut

Top side

Surprise underneath!!

So happy together

At da beach….

With the oxygen levels dropping in the ocean as sea temperatures rise, expect to see more jellyfish (and colonies). They serve as a canary in the coal mine, if you will.

At least the signs of our stupidity will look pretty….

Keep overthinkin’ it

Eco Surf Hippie Beanbag Pillow

I’m the first to admit I’m a material hoarder. Lots of people don’t realize that clothing makes up a large fraction of landfill trash, and these days, much of it is synthetic and breaks down slowly.

I like to save old Lycra from random rashguards and surf gear, so I decided to cut pieces up into small quilt squares to make a simple two sided squishy pillow filled with scrap neoprene. Woah…that’s being supa Bro–active about our environment, yo.

Pile o’ Lycra

Cutting pieces into smaller squares from various pieces

Laying out a fun pattern

I serged into rows first

Layout of the other side of the pillow

Both sides of the pillow

Pinning the pillow to stitch it up before stuffing

Neoprene beans from wetsuits

I stuffed the pillow casing I made with quite a bit of the cut up neoprene “beans” I had cut up previously (see this project).

Clipped the opening closed and I whip stitched it closed

Done!

That’ll fit my rear, watch out, Max….

So I figure this pillow with be perfect for the beach, since I can rinse it off, toss it in the wash with no worries, and it’s small enough to sling over my bag.

Hey, if this helps the environment, great. I mean, it’s your world, brah.

Try me……but have a nice day

DIY Surfboard Leash Cord Mod

The surfboard leash, in my opinion, is a good thing.

Have them pull a sled next time

Talk to some “old school” surfers, and they’ll call it a Kook Cord, meaning that only newer, clumsier surfers require being attached to their surf craft. I say leashes are litigation deterrents- a little insurance in a crowded lineup of surfers and swimmers. If I’m alone and the surf’s small, okay, I’ll skip da leash. Otherwise, better to be safe all around.

My issue has been finding a decent lightweight leash that’s 9′ long to use with my longboards. The Comp weight doesn’t seem to tangle as much as the thicker cord types, but the 9’+ length can be tricky to find. I’m never going to surf Pipeline, so I don’t need the reinforced titanium nitro supa thick variety. Also, for longboarding, I like to use a Knee Leash as opposed to an Ankle Leash to help keep it from being tangled around my feet. Hopefully.

I ended up buying an XM 9′ Comp leash I found and just wrapping the ankle strap around my knee instead.

Freakin’ hurts

Ow. The exposed edges of the Velcro raked the heck out of the back of my knee after a few weeks of use. Since open wounds and ocean water make for a doctor’s visit, I decided to make the strap a bit more comfy.

First, I took off the side of the strap with a seam ripper.

It came apart pretty easily

I saved the pull tab to reattach it later

Using some scrap neoprene taken from the chest panel of an old wetsuit, I made an extender strip as wide as the original leash strap.

I used the chest panel since it’s got a rubber layer over the neoprene

Once I had my new longer neoprene strip ready, I glued it back into place using E6000 industrial glue. I had some nylon thread as a backup, but I didn’t need it! Woo Hoo!

I sandwiched one end with glue on both sides

I used quilting clips to hold everything in place while it dried

Next, I took a bit of the loopy side of some 2″ Industrial Velcro and used glue with the adhesive on the back of the strip, similar to what I did on the Board Bag mod.

I used a lot of glue

Clamped and drying

I gave the leash about 48 hours inside to fully cure, since the weather’s been so hot.

Much better!!!!

After surfing with it

It feels MUCH better on my leg now, with no more burn. Hey- if I’m going to get rug burn from Velcro, I’m going full YOLO….

Aim high kids

Felt Fin Fun!

Like most crafters, I’m on Pinterest a lot, and not just for the hella dank memes. I’ve been clicking around some of the neato felt embroidery I’ve seen pinned lately, and decided to make a fun felt stuffie from a tracing of one of my longboard fins.

Certified DANK

Acrylic felt is pretty cheap, and if you can find the type made from recycled soda bottles, extra eco-hippie-surfer cred points for you. I also used basic embroidery thread and some poly stuffing. All can be found at any local craft store.

My supplies

Tracing the fin template

I went crazy cutting out shapes to sew on

Makin’ flowers

Adding in detail

Chain stitching the vines

I even added beads!

Blanket stitching the two sides together

I didn’t overstuff

I crocheted the edge and added a hang loop

Finished edge

Completed Stuffie!

So this is purely for fun, so I’m going to put it on the cool felt Lei I made for TikiMan a while back. It’s like a funky fresh headpiece:

Can you dig it???

I can see myself making a few of these little felt stuffies for kicks, especially in the afternoons since it’s been so freakin’ hot here. I mean, I did find an image on Pinterest that sums up Florida surfing perfectly…..

Do you think the wax is still good???

Surfboard Bag Rehab

While we were sifting around the junk in the garage last week, I noticed an old longboard travel bag that I won at a surf event several years ago. I’ve loaned it out many times to my friends who go on trips, so the bag is more surf-travelled than I am.

Might still have some life yet

The zipper pull is stuck and crusted from salt, and the plastic zipper teeth themselves have started to deteriorate.

It’s stuck

That’s just nasty

It’s not currently usable with the zipper almost completely disintegrated, so it had to be removed.

Seam ripper- this was a good section

Taking out the zipper took a while!

Unfortunately, a replacement zipper must be at least 10 feet long for this particular bag, and I cannot sew it in with my home sewing machine. Nor would I want to.

Enter Industrial Velcro. You can pick it up at most big box stores or hardware stores for less than 10 bucks for 10 feet. I used titanium scissors to cut 2 inch strips of the soft loopy side of the Velcro first to put on the sides of the board bag.

Just cutting the soft loopy side of the Velcro- keep the adhesive backing on

I placed one of these squares around the sides about every ten inches or so

I needed to put additional E6000 glue under the adhesive Velcro since Florida’s so freakin’ hot that I thought the Velcro adhesive would melt. I was right.

Next, I made straps for the top cover of the bag by cutting 8″ strips of 2″ wide webbed nylon strapping, turning one edge under and gluing it with E6000. This makes a sturdy edge to pull on.

My supplies

I turned the bottom of the strap up about an inch and glued it, holding it in place with clips

I cut 2” squares of the hook side of the Velcro to go on the underside of the straps

The straps glued up and drying

Once the straps were dried and the loopy patches on the board bag were dry, I was ready to affix the straps to the cover. At this point, I put one of my surfboards in the bag to fill it out properly for correct strap placement.

Once again, I used plenty of E6000 glue…

If it goes out to the edge, all the better

Glad textbooks are still good for something

I had to take everything indoors to allow the glue to cure properly since it’s a million degrees outside. I just made sure to keep everything ventilated. I also allowed everything to dry for over 24 hours since the bag will be taking a lot of stress.

Done!

Peels right open like a banana

Good enough for a trip up the street

Although this bag may not be suitable for plane travel anymore, it’s good enough for local travel. This may help keep some of the nasty sand, salt, and wax off of the roof of my car as a bonus. Since the cover just peels off and peels back on easily enough to load it in and out of the bag, it may actually get used now.

Hey, I’m might be a hick, but even I don’t want my little car to get THIS bad….

Hillbilly Surf Shop sounds like they know me well

Boardshort Hack Attack

If you follow my blog, you may already know I freakin’ love boardshorts. I will also wear them while surfing too, since few people appreciate me duckdiving a wave in a thong. Their loss.

Christmas in July

Anywho, I picked up this pair of Quiksilver Waterman Boardshorts a while back. I love them except for the thicky-thick tie that came with it. It’s bulgy, doesn’t stay tied, and hurts when I lay on my board to paddle. Time for a makeover.

Nice except for the crappy tie

This tie NEVER stays tied

I gathered some 1/4″ flat elastic, a needle and thread, some scissors, and a seam ripper (if needed).

My supplies

The tie was sewn into the shorts, so I had to use my seam ripper to remove it:

Removing the original tie

Taking just a small length of the flat elastic, I laced it through the grommets of the shorts’ fly from the TOP DOWN. This is important since I want to join the elastic together at the BOTTOM, where the elastic won’t get as much action. I pulled the sides of the fly together flush, and pinned the elastic ends together where it’s comfortable.

Laced through, ends come out on the INSIDE of the fly

Sewing the elastic ends together

Looking inside the fly, the ends have been clipped and sewn

Completed!

Pull on and off!!

This now stays flat, pulls on and off easily, and there’s no need to worry about my shorts staying tied finally.

I’m so happy that the biggest pressing concern is chafing my belly button when I surf. It can ALWAYS be worse, brah….

Get him a ticket to Tahiti NOW