DIY Surfboard Leash Cord Mod

The surfboard leash, in my opinion, is a good thing.

Have them pull a sled next time

Talk to some “old school” surfers, and they’ll call it a Kook Cord, meaning that only newer, clumsier surfers require being attached to their surf craft. I say leashes are litigation deterrents- a little insurance in a crowded lineup of surfers and swimmers. If I’m alone and the surf’s small, okay, I’ll skip da leash. Otherwise, better to be safe all around.

My issue has been finding a decent lightweight leash that’s 9′ long to use with my longboards. The Comp weight doesn’t seem to tangle as much as the thicker cord types, but the 9’+ length can be tricky to find. I’m never going to surf Pipeline, so I don’t need the reinforced titanium nitro supa thick variety. Also, for longboarding, I like to use a Knee Leash as opposed to an Ankle Leash to help keep it from being tangled around my feet. Hopefully.

I ended up buying an XM 9′ Comp leash I found and just wrapping the ankle strap around my knee instead.

Freakin’ hurts

Ow. The exposed edges of the Velcro raked the heck out of the back of my knee after a few weeks of use. Since open wounds and ocean water make for a doctor’s visit, I decided to make the strap a bit more comfy.

First, I took off the side of the strap with a seam ripper.

It came apart pretty easily

I saved the pull tab to reattach it later

Using some scrap neoprene taken from the chest panel of an old wetsuit, I made an extender strip as wide as the original leash strap.

I used the chest panel since it’s got a rubber layer over the neoprene

Once I had my new longer neoprene strip ready, I glued it back into place using E6000 industrial glue. I had some nylon thread as a backup, but I didn’t need it! Woo Hoo!

I sandwiched one end with glue on both sides

I used quilting clips to hold everything in place while it dried

Next, I took a bit of the loopy side of some 2″ Industrial Velcro and used glue with the adhesive on the back of the strip, similar to what I did on the Board Bag mod.

I used a lot of glue

Clamped and drying

I gave the leash about 48 hours inside to fully cure, since the weather’s been so hot.

Much better!!!!

After surfing with it

It feels MUCH better on my leg now, with no more burn. Hey- if I’m going to get rug burn from Velcro, I’m going full YOLO….

Aim high kids

Felt Fin Fun!

Like most crafters, I’m on Pinterest a lot, and not just for the hella dank memes. I’ve been clicking around some of the neato felt embroidery I’ve seen pinned lately, and decided to make a fun felt stuffie from a tracing of one of my longboard fins.

Certified DANK

Acrylic felt is pretty cheap, and if you can find the type made from recycled soda bottles, extra eco-hippie-surfer cred points for you. I also used basic embroidery thread and some poly stuffing. All can be found at any local craft store.

My supplies

Tracing the fin template

I went crazy cutting out shapes to sew on

Makin’ flowers

Adding in detail

Chain stitching the vines

I even added beads!

Blanket stitching the two sides together

I didn’t overstuff

I crocheted the edge and added a hang loop

Finished edge

Completed Stuffie!

So this is purely for fun, so I’m going to put it on the cool felt Lei I made for TikiMan a while back. It’s like a funky fresh headpiece:

Can you dig it???

I can see myself making a few of these little felt stuffies for kicks, especially in the afternoons since it’s been so freakin’ hot here. I mean, I did find an image on Pinterest that sums up Florida surfing perfectly…..

Do you think the wax is still good???

Boardshort Hack Attack

If you follow my blog, you may already know I freakin’ love boardshorts. I will also wear them while surfing too, since few people appreciate me duckdiving a wave in a thong. Their loss.

Christmas in July

Anywho, I picked up this pair of Quiksilver Waterman Boardshorts a while back. I love them except for the thicky-thick tie that came with it. It’s bulgy, doesn’t stay tied, and hurts when I lay on my board to paddle. Time for a makeover.

Nice except for the crappy tie

This tie NEVER stays tied

I gathered some 1/4″ flat elastic, a needle and thread, some scissors, and a seam ripper (if needed).

My supplies

The tie was sewn into the shorts, so I had to use my seam ripper to remove it:

Removing the original tie

Taking just a small length of the flat elastic, I laced it through the grommets of the shorts’ fly from the TOP DOWN. This is important since I want to join the elastic together at the BOTTOM, where the elastic won’t get as much action. I pulled the sides of the fly together flush, and pinned the elastic ends together where it’s comfortable.

Laced through, ends come out on the INSIDE of the fly

Sewing the elastic ends together

Looking inside the fly, the ends have been clipped and sewn

Completed!

Pull on and off!!

This now stays flat, pulls on and off easily, and there’s no need to worry about my shorts staying tied finally.

I’m so happy that the biggest pressing concern is chafing my belly button when I surf. It can ALWAYS be worse, brah….

Get him a ticket to Tahiti NOW