Eco Surf Hippie Beanbag Pillow

I’m the first to admit I’m a material hoarder. Lots of people don’t realize that clothing makes up a large fraction of landfill trash, and these days, much of it is synthetic and breaks down slowly.

I like to save old Lycra from random rashguards and surf gear, so I decided to cut pieces up into small quilt squares to make a simple two sided squishy pillow filled with scrap neoprene. Woah…that’s being supa Bro–active about our environment, yo.

Pile o’ Lycra

Cutting pieces into smaller squares from various pieces

Laying out a fun pattern

I serged into rows first

Layout of the other side of the pillow

Both sides of the pillow

Pinning the pillow to stitch it up before stuffing

Neoprene beans from wetsuits

I stuffed the pillow casing I made with quite a bit of the cut up neoprene “beans” I had cut up previously (see this project).

Clipped the opening closed and I whip stitched it closed

Done!

That’ll fit my rear, watch out, Max….

So I figure this pillow with be perfect for the beach, since I can rinse it off, toss it in the wash with no worries, and it’s small enough to sling over my bag.

Hey, if this helps the environment, great. I mean, it’s your world, brah.

Try me……but have a nice day

DIY Surfboard Leash Cord Mod

The surfboard leash, in my opinion, is a good thing.

Have them pull a sled next time

Talk to some “old school” surfers, and they’ll call it a Kook Cord, meaning that only newer, clumsier surfers require being attached to their surf craft. I say leashes are litigation deterrents- a little insurance in a crowded lineup of surfers and swimmers. If I’m alone and the surf’s small, okay, I’ll skip da leash. Otherwise, better to be safe all around.

My issue has been finding a decent lightweight leash that’s 9′ long to use with my longboards. The Comp weight doesn’t seem to tangle as much as the thicker cord types, but the 9’+ length can be tricky to find. I’m never going to surf Pipeline, so I don’t need the reinforced titanium nitro supa thick variety. Also, for longboarding, I like to use a Knee Leash as opposed to an Ankle Leash to help keep it from being tangled around my feet. Hopefully.

I ended up buying an XM 9′ Comp leash I found and just wrapping the ankle strap around my knee instead.

Freakin’ hurts

Ow. The exposed edges of the Velcro raked the heck out of the back of my knee after a few weeks of use. Since open wounds and ocean water make for a doctor’s visit, I decided to make the strap a bit more comfy.

First, I took off the side of the strap with a seam ripper.

It came apart pretty easily

I saved the pull tab to reattach it later

Using some scrap neoprene taken from the chest panel of an old wetsuit, I made an extender strip as wide as the original leash strap.

I used the chest panel since it’s got a rubber layer over the neoprene

Once I had my new longer neoprene strip ready, I glued it back into place using E6000 industrial glue. I had some nylon thread as a backup, but I didn’t need it! Woo Hoo!

I sandwiched one end with glue on both sides

I used quilting clips to hold everything in place while it dried

Next, I took a bit of the loopy side of some 2″ Industrial Velcro and used glue with the adhesive on the back of the strip, similar to what I did on the Board Bag mod.

I used a lot of glue

Clamped and drying

I gave the leash about 48 hours inside to fully cure, since the weather’s been so hot.

Much better!!!!

After surfing with it

It feels MUCH better on my leg now, with no more burn. Hey- if I’m going to get rug burn from Velcro, I’m going full YOLO….

Aim high kids

Felt Fin Fun!

Like most crafters, I’m on Pinterest a lot, and not just for the hella dank memes. I’ve been clicking around some of the neato felt embroidery I’ve seen pinned lately, and decided to make a fun felt stuffie from a tracing of one of my longboard fins.

Certified DANK

Acrylic felt is pretty cheap, and if you can find the type made from recycled soda bottles, extra eco-hippie-surfer cred points for you. I also used basic embroidery thread and some poly stuffing. All can be found at any local craft store.

My supplies

Tracing the fin template

I went crazy cutting out shapes to sew on

Makin’ flowers

Adding in detail

Chain stitching the vines

I even added beads!

Blanket stitching the two sides together

I didn’t overstuff

I crocheted the edge and added a hang loop

Finished edge

Completed Stuffie!

So this is purely for fun, so I’m going to put it on the cool felt Lei I made for TikiMan a while back. It’s like a funky fresh headpiece:

Can you dig it???

I can see myself making a few of these little felt stuffies for kicks, especially in the afternoons since it’s been so freakin’ hot here. I mean, I did find an image on Pinterest that sums up Florida surfing perfectly…..

Do you think the wax is still good???

Surfboard Bag Rehab

While we were sifting around the junk in the garage last week, I noticed an old longboard travel bag that I won at a surf event several years ago. I’ve loaned it out many times to my friends who go on trips, so the bag is more surf-travelled than I am.

Might still have some life yet

The zipper pull is stuck and crusted from salt, and the plastic zipper teeth themselves have started to deteriorate.

It’s stuck

That’s just nasty

It’s not currently usable with the zipper almost completely disintegrated, so it had to be removed.

Seam ripper- this was a good section

Taking out the zipper took a while!

Unfortunately, a replacement zipper must be at least 10 feet long for this particular bag, and I cannot sew it in with my home sewing machine. Nor would I want to.

Enter Industrial Velcro. You can pick it up at most big box stores or hardware stores for less than 10 bucks for 10 feet. I used titanium scissors to cut 2 inch strips of the soft loopy side of the Velcro first to put on the sides of the board bag.

Just cutting the soft loopy side of the Velcro- keep the adhesive backing on

I placed one of these squares around the sides about every ten inches or so

I needed to put additional E6000 glue under the adhesive Velcro since Florida’s so freakin’ hot that I thought the Velcro adhesive would melt. I was right.

Next, I made straps for the top cover of the bag by cutting 8″ strips of 2″ wide webbed nylon strapping, turning one edge under and gluing it with E6000. This makes a sturdy edge to pull on.

My supplies

I turned the bottom of the strap up about an inch and glued it, holding it in place with clips

I cut 2” squares of the hook side of the Velcro to go on the underside of the straps

The straps glued up and drying

Once the straps were dried and the loopy patches on the board bag were dry, I was ready to affix the straps to the cover. At this point, I put one of my surfboards in the bag to fill it out properly for correct strap placement.

Once again, I used plenty of E6000 glue…

If it goes out to the edge, all the better

Glad textbooks are still good for something

I had to take everything indoors to allow the glue to cure properly since it’s a million degrees outside. I just made sure to keep everything ventilated. I also allowed everything to dry for over 24 hours since the bag will be taking a lot of stress.

Done!

Peels right open like a banana

Good enough for a trip up the street

Although this bag may not be suitable for plane travel anymore, it’s good enough for local travel. This may help keep some of the nasty sand, salt, and wax off of the roof of my car as a bonus. Since the cover just peels off and peels back on easily enough to load it in and out of the bag, it may actually get used now.

Hey, I’m might be a hick, but even I don’t want my little car to get THIS bad….

Hillbilly Surf Shop sounds like they know me well

Boardshort Hack Attack

If you follow my blog, you may already know I freakin’ love boardshorts. I will also wear them while surfing too, since few people appreciate me duckdiving a wave in a thong. Their loss.

Christmas in July

Anywho, I picked up this pair of Quiksilver Waterman Boardshorts a while back. I love them except for the thicky-thick tie that came with it. It’s bulgy, doesn’t stay tied, and hurts when I lay on my board to paddle. Time for a makeover.

Nice except for the crappy tie

This tie NEVER stays tied

I gathered some 1/4″ flat elastic, a needle and thread, some scissors, and a seam ripper (if needed).

My supplies

The tie was sewn into the shorts, so I had to use my seam ripper to remove it:

Removing the original tie

Taking just a small length of the flat elastic, I laced it through the grommets of the shorts’ fly from the TOP DOWN. This is important since I want to join the elastic together at the BOTTOM, where the elastic won’t get as much action. I pulled the sides of the fly together flush, and pinned the elastic ends together where it’s comfortable.

Laced through, ends come out on the INSIDE of the fly

Sewing the elastic ends together

Looking inside the fly, the ends have been clipped and sewn

Completed!

Pull on and off!!

This now stays flat, pulls on and off easily, and there’s no need to worry about my shorts staying tied finally.

I’m so happy that the biggest pressing concern is chafing my belly button when I surf. It can ALWAYS be worse, brah….

Get him a ticket to Tahiti NOW

DIY 4Ocean Charm Earrings

Remember that necklace/wrap bracelet I made a couple of posts ago? I saved the little silver charms from the 4Ocean bracelets, and I wanted to use them to make some easy fun earrings with basic stuff from the craft store. Ear hooks, a few glass beads, and a couple of eye pins can make a fancy looking pair of earrings. You’ll also need a pair of small round-nose jewelry making pliers (here’s a link to some I found online).

All of my supplies

Adding a charm to the end of each eye pin

Sliding a silver bead, a glass fish bead, then a silver bead onto each eye pin

Preparing to make a loop at the top of each eye pin

I try to match up the same position when I make the loop on each

Done!

Ear selfie

These are a cute way to promote the 4Ocean cause of removing plastics from the ocean, and creating awareness of plastic pollution.

Honestly, though, for surfing the Cocoa Beach Pier, I need more useful earrings. I searched on Etsy and found my dream pair:

OFF MY WAVE WANKER

DIY 4Ocean + CapeClasp Wrap Bracelet or Necklace

This is a project I’ve wanted to do for a while. I had a couple of 4Ocean recycled glass bracelets and a silver shark toggle from Cape Clasp I’ve been wanting to combine into something FUNNER.

Wave at da haters

Both of these companies raise money for ocean related charities, which is always a good excuse to buy pretty things, ya know. And by the way, I don’t shill for these companies, I had to buy ’em just like everyone else.

For this project, I used my two 4Ocean bracelets, my Cape Clasp Hammerhead shark toggle (removed from the paracord), scissors, and some Chinese Knotting cord (I used dark green), which is essentially VERY thin nylon paracord. I used a little over 3 yards for this, folded in half. Glue may be handy to secure the finishing knot.

My supplies

Recycled beauties!

Saving the charms for another project

I made a lark’s head loop over the tail hole and made an overhand knot. I slid a recycled glass bead over both cords, and made another overhand knot, snugging it up against the bead. Repeat until all the beads are gone.

Lark’s head loop over tail

Overhand knot between each bead

For the loop, I took the cords and made alternating half hitches until the loop was long enough to secure over the toggle, then I secured it with a square knot and melted the ends with a lighter (outside!).

Alternating half hitch knots

Toggle secured

Done! It came out to around 20″ when it was complete, long enough for a necklace or a wrist wrap.

The Country Club Surfer

A halfway decent strand of Mikimoto’s will set you back several grand, but I figure this hundred dollar DIY set might help out a bit more.

I let it all go a looong time ago, kids